Teamwork CNS Inc.
Teamwork CNS Inc.
Sinthee, Kolkata, West Bengal
SEND SMS
SEND EMAIL

Bearing Induction Heater

Pioneers in the industry, we offer Bearing Induction Heater, Bearing Heater, Induction Heater for Bearing, Induction Bearing Heater and Portable Bearing Induction Heater from India.

Bearing Induction Heater

Bearing Induction Heater
  • Bearing Induction Heater
Get Best Quote
Approx. Price: Rs 5 Lakh / Piece

Product Details:

Minimum Order Quantity1 Piece
Frequency (Hz)50 - 60
Power3 - 11 KVA
Weight90 kg
Automatic Power ReductionYes
ApplicationChemical Industry, Steel Industry, Paper Industry

Our company deals in distribution of a wide array of Bearing Induction Heater which is manufactured in compliance with industry standard. Various induction heaters available to us are small, medium, large induction heaters. 
Induction heating is a superior, fast and controlled heating method. It is a safe and environmentally-friendly alternative to traditional heating methods such as ovens, oil baths or blow torches. These methods generate smoke, fumes or oil waste and are hazardous for personal health and safety.

FOR BEARINGS AND OTHER COMPONENTS BETEX  induction heaters are versatile and can be used for the heating of gear wheels, bushes, couplings, etc. It is common knowledge that a correct mounting method extends bearing life. Even, tension-free heating prevents unnecessary damage and retains original lubrication. Induction heaters are ideal for sealed (2RS-ZZ) and pre-lubricated bearings.
ADVANTAGES OF BETEX INDUCTION HEATERS:
Robust design for working in industrial environments.  
Evenly distributed heating: the microprocessor con- trolled electronics prevent overheating and explosive heating.   
For sealed (2RS-ZZ) and pre-lubricated bearings. 
Automatic power reduction.  
Automatic demagnetisation to <2A/cm.  
Unique, user-friendly swivel-arm construction.  
Suitable for continuous use (24/7).  
Large selection from STANDARD and TURBO series, from 3.6 to 100 kVA.

TURBO models are energy efficient.   Portable models for on-site works.  3 year warranty on electrical unit.   Meets CE and IEC requirements. 

SAFE AND CONTROLLED HEATING Digital electronics ensure optimum control during the heating process. These automatically regulate the most efficient use of power and ensure even and rapid heating. No extra steps are necessary. This prevents explosive heating (no discolouration or pitting of material).

Basic bench-top type with swivel arm for use in the workshop.

Min. ID: 15 mm  Max. OD: 380 mm  Max. width: 150 mm  Automatic demagnetisation Automatic power reduction  Yokes: set of 3 or 5 sizes
Max. bearing weight: 65 kg  Max. weight other parts: 30 kg
Optional: Adaptor yokes Max. OD : 580 mm
Request
Callback
Yes! I am Interested
View PDF

Bearing Heater

Bearing Heater
  • Bearing Heater
  • Bearing Heater
Get Best Quote
Approx. Price: Rs 4 Lakh / Piece

Product Details:

Minimum Inner Diameter15 mm
Maximum Outer Diameter520 mm
Maximum Width230 mm
Automatic Power ReductionYes
Weight95 kg
ApplicationChemical Industry, Steel Industry, Paper Industry and Gear Box Manufacturing etc

—  Induction heating is a superior, fast and controlled heating method.

—  It is a safe and environmentally-friendly alternative to traditional heating methods such as ovens, oil baths or blow torches. These methods generate smoke, fumes or oil waste and are hazardous for personal health and safety.

—  BETEX® induction heaters are versatile and can be used for the heating of gear wheels, bushes, couplings, etc. It is common knowledge that a correct mounting method extends bearing life. Even, tension-free heating prevents unnecessary damage and retains original lubrication.

—  Induction heaters are ideal for sealed (2RS-ZZ) and pre-lubricated bearings.

WORKING PRINCIPLE:

—  The heater works by inducing a (low frequency) current in the component to be heated. This is achieved by incorporating the component as a secondary winding in a transformer. The primary winding is connected to the mains power by means of an electronic control. The magnetic field induces a high current (short circuit current) through the component which consequently becomes hot. The work piece is automatically demagnetised after every heating cycle.

—  STANDARD SERIES:

i) Betex 22 ELD - PortableMin. ID Ø: 10 mm , Max. OD Ø: 240 mm, For bearings up to ± 15 kg.

ii)  Betex 22 ESD- Min. ID Ø: 15 mm, Max. OD Ø: 340 mm, For bearings up to ± 40 kg

iii) Betex 38 ESD- Min. ID Ø: 30 mm, Max. OD Ø: 480 mm, For bearings up to ± 125 kg.

iv) Betex SUPER- Min. ID Ø: 60 mm, Max. OD Ø: 1300 mm, For bearings up to ± 600 kg

·         TURBO SERIES:

i) Betex 24 RLD TURBO- PortableMin. ID Ø: 10 mm, Max. OD Ø: 350 mm, For bearings up to ± 40 kg.

ii) Betex 24 RSD TURBO- Min. ID Ø: 15 mm, Max. OD Ø: 520 mm, For bearings up to ± 95 kg.
iii)  Betex 40 RSD TURBO- Min. ID Ø: 30 mm, Max. OD Ø: 790 mm, For bearings up to ± 350 kg.

iv) Betex GIANT- Min. ID Ø: 85 mm, Max. OD Ø: 1400-2500 mm, For bearings from ± 1500 up to ± 3500 kg. 

Request
Callback


Additional Information:

  • Item Code: 14
Yes! I am Interested

Induction Heater for Bearing

Induction Heater for Bearing
  • Induction Heater for Bearing
Get Best Quote
Approx. Price: Rs 5 Lakh / Piece

Product Details:

Minimum Order Quantity1 Piece
Frequency (Hz)50
Voltage400 - 500 V
Weight53 kg
Power8.0 KVA
PhaseThree Phase
Display TypeDigital
Working Temperature240 Degree Celcius
Maximum Bearing Weight125 kg

The heater works by inducing a (low frequency) current in the component to be heated. This is achieved by incorporating the component as a secondary winding in a transformer. The primary winding is connected to the mains power by means of an electronic control. The magnetic field induces a high current (short circuit current) through the component which consequently becomes hot. The work piece is automatically demagnetised after every heating cycle.

BETEX 38 ESD microprocessor controlled bearing induction heater, Three phase 400/500 V, 50 Hz, 8.0 Kva with  the unique Betex swing arm construction, and supports for horizontal heating.

YOKE 30, 70 mm, max. temperature 240°C, digital display, incl. magnetic probe, automatic demagnetization, better than 2A/cm, time or temperature pre selection, acoustic signal at the end of each heating cycle , provided with audio alarm in reaching set temperature, temperature hold, incl. service kit and CE-manual,

TECHNICAL SPECIFICATION :

  1. Capacity-   Maximum bearing weight- 150 kgs.,
  2. Bore diameter-  30 mm, max. outside diameter- 500 mm/720 mm ( With extension yokes),
  3. Temperature range- Up to 240 degree centigrade,
  4. Digital display with electronic timer with range minimum 0 to 60 minutes,
  5. Automatic demagnetization ( residual magnetism < 2.0 Amps) and will be furnished with fast acting temperature probe,
  6. The bearing induction heater have thermal over heating protection,
  7. The bearing induction heater would be equipped with magnetic temperature sensor,
  8. Weight of heater body (Excluding yokes)- 53 kg.
Request
Callback


Additional Information:

  • Item Code: 15
Yes! I am Interested

Induction Bearing Heater

Induction Bearing Heater
  • Induction Bearing Heater
Get Best Quote
Approx. Price: Rs 5 Lakh / Piece

Product Details:

Frequency (Hz)60
Voltage240 V
Minimum Inner Diameter30 mm
Maximum Outer Diameter240 - 1300 mm
Maximum Bearing Weight15 - 600 kg
Weight50 kg

The Induction Bearing Heater works by inducing a (low frequency) current in the component to be heated. This is achieved by incorporating the component as a secondary winding in a transformer. 

BETEX 24 RSD TURBO microprocessor controlled bearing induction heater, Single phase, 50 Hz, 3.6 Kva with the unique Betex swing arm construction, and supports for horizontal heating. Yoke  14,30, 60 mm, max. temperature 240°C, digital display, incl. magnetic probe, automatic demagnetization, better than 2A/cm, time or temperature pre selection, acoustic signal at the end of each heating cycle , provided with audio alarm in reaching set temperature, temperature hold, incl. service kit and CE-manual.

Supplied with – Magnetic Temperature Probe with Cable & Socket Holder, Hand Gloves-01 Pair.

Main Equipment in reinforced Fiberglass body, Hermetically sealed coil, Automatic Demagnetizing cycle.

 

TECHNICAL SPECIFICATION :

  1. Capacity-   Maximum bearing weight- 150 kgs. Maximum Weight of other Components- 80 KG,  
  2. Bore diameter- Minimum ID- 15 mm , max. Outside diameter- 520 mm.
  3. Temperature range- Up to 240 degree centigrade,
  4. Digital display with electronic timer with range minimum 0 to 45 minutes,
  5. Automatic demagnetization ( residual magnetism < 2.0 Amps) and will be furnished with fast acting temperature probe,
  6. The bearing induction heater have thermal over heating protection,
  7. The bearing induction heater would be equipped with magnetic temperature sensor,
  8.  Would be provided with audio alarm.
  9. Pole height- 230 mm and Maximum bearing width- 230 mm.
  10. Weight of heater body- 37 kg.
  11. Dimensions: 440 x 370 x 420 mm,
  12. Yoke size- 14 x 14  x 280 mm, 30 x 30 x 280 mm, 60 x 60 x 280 mm

 

 

Request
Callback
Yes! I am Interested

Portable Bearing Induction Heater

Portable Bearing Induction Heater
  • Portable Bearing Induction Heater
Get Best Quote
Approx. Price: Rs 2.5 Lakh / Piece

Product Details:

Minimum Inner Diameter10 mm
Maximum Outer Diameter350 mm
Maximum Width135 mm
Maximum Bearing Weight40 kg
Weight25 kg

FOR BEARINGS AND OTHER COMPONENTS BETEX  induction heaters are versatile and can be used for the heating of gear wheels, bushes, couplings, etc. It is common knowledge that a correct mounting method extends bearing life. Even, tension-free heating prevents unnecessary damage and retains original lubrication. Induction heaters are ideal for sealed (2RS-ZZ) and pre-lubricated bearings.

Type Betex 24 RLDi TURBO Portable, Micro-processor controlled,  Portable type bearing induction heater,

1) Supply voltage-  230V AC  ( 50 Hz),
2) Power consumption- 3.6 KVA,
3) Temp. control range- 0-240 * C, (+/- 1 Degree C),
4) Time control range- 0-45 minutes,
5) Range of work piece dia. – maximum OD- 380 mm, minimum ID- 10 mm, Maximum width of work piece- 135 mm,
6) Max. weight of work piece can be heated- for bearing- 50 kgs.
7) Automatic demagnetization better than 2A/cm.
8) Ability to heat sealed and pre-greased bearings.
9) Weight of unit excluding of yokes- 23 kgs,
10) Work piece can be heated in horizontal and vertical position.
11) Bearing heater is portable type,
12) Having thermal overload protection,
13) Power reduction- automatic,
14) Yoke for bearing heating will be provided With   20 x 20 x 250 mm, 30 x 30 x 250 mm and 40 x 40 x 250 mm,
15) The heater having temperature showing LED display to show temperature.
Request
Callback


Additional Information:

  • Item Code: 13
Yes! I am Interested
View PDF
X

Explore more products

Looking for “Bearing Induction Heater”?


Reach Us
Sanjoy Mazumder (Manager Customer Support)
494B/A, East Sinthee Road, Dum Dum
Kolkata- 700030, West Bengal, India



Call Us

Share Us

F GT L


Send E-mailSend SMS